Differences

This shows you the differences between two versions of the page.

--- orangepi_800 [2024/01/24 13:05] – austin
+++ orangepi_800 [2024/09/22 22:08] (current) – external edit 127.0.0.1
@@ Line 61: / Line 61: @@
   * now portage should work
+  * update ca's
+<code>
+emerge --ask app-misc/ca-certificates
+</code>
 === wifi setup ===
@@ Line 104: / Line 109: @@
 passwd foobar
 </code>
+===== connecting UART =====
+To enable serial console in gentoo edit inittab:
+<code>
+f0:12345:respawn:/sbin/agetty 1500000 ttyS2 vt100
+</code>
+{{:screenshot_2024-01-24_at_8.08.17 am.png?400|pi800 uart connection}}
+^DTECH UART Cable^^
+|White|RXD|
+|Green|TXD|
+|Black|GND|
+|Red|VCC +5V|
+<code>
+su -
+screen /dev/ttyUSB0 1500000
+</code>
+===== Kernel... =====
+Existing kernel doesn't have required settings for GPU!!! Really this is the kernel from vendor supplied image.  It's really old, 5.10 so working an updated kernel.
+<code>
+# CONFIG_DRM_PANFROST is not set
+</code>
+The reason it is not set is the code is broken.
+[[https://github.com/orangepi-xunlong/linux-orangepi/tree/orange-pi-5.10-rk3399/arch/arm64/boot/dts/rockchip|Source]]
+<code>
+drivers/gpu/drm/panfrost/panfrost_mmu.c:359:10: error: 'const struct iommu_flush_ops' has no member named 'tlb_flush_leave'; did you mean'tlb_flush_all'?
+</code>
+Looking at  a newer kernel that line doesn't exist so I removed it.
+<code>
+static const struct iommu_flush_ops mmu_tlb_ops = {
+	.tlb_flush_all	= mmu_tlb_inv_context_s1,
+	.tlb_flush_walk = mmu_tlb_flush_walk,
+};
+</code>
+It compiles now, but I wonder if I should remove this function as well(I guess I'll do some testing and decide):
+<code>
+static void mmu_tlb_flush_leaf(unsigned long iova, size_t size, size_t granule,
+			       void *cookie)
+{
+	mmu_tlb_sync_context(cookie);
+}
+</code>
+The module compiles and loads but isn't really functional now.
+The orangepi ubuntu based image uses this [[https://github.com/orangepi-xunlong/linux-orangepi/tree/orange-pi-5.18|kernel(5.18)]].  Its slightly newer.  I couldn't get it to work with module compression(enabled with XZ compression in the image).  It threw an error whenever trying to load a module.  Which is really weird as I initially just copied the kernel and modules from the image and it works fine with their image.  Something must prevent this from working with the openrc-stage3 from Gentoo but I didn't dig real deep into this.  After recompiling without module compression it works other than rfkill.ko appears to hang when loading on boot (required by sprdwl_ng) but eventually completes loading and works fine so I've switched to this kernel for the time being.
+Found more recent [[https://github.com/zhangn1985/linux-stable|source(6.8-rc2)]]. It compiles and I get video output but it hangs on first daemon load.  This is going to require some more work.
+===== references =====
+[[https://github.com/orangepi-xunlong/orangepi-build/tree/next|Linux Source]]
+{{ :methods_of_writing_images_on_opi800.pdf |Orange Pi800 sad excuse for a manual}}
+[[https://opensource.rock-chips.com/wiki_Boot_option|Rockchip Wiki - Booting]]
+[[https://wiki.gentoo.org/wiki/User:PeterL/Rockpro64|Gentoo Doc for Rockpro64(same soc)]]
+[[https://github.com/ARM-software/arm-trusted-firmware|Arm Trusted Firmware]]

Adrenlinerush Wiki

User Tools

Site Tools

Differences

Page Tools